Loading... Please wait...
  • JMS Progressive Nitrous Controller pn: 6021 Maximum Nitrous Control all in a simple to use package.  Only a screwdriver is required.  Built in window switch, handles up to 55amps, independent fuel/nos solenoid control!!
  • JMS Progressive Nitrous Controller pn: 6021 Maximum Nitrous Control all in a simple to use package.  Only a screwdriver is required.  Built in window switch, handles up to 55amps, independent fuel/nos solenoid control!!
  • Generic JMS Progressive Nitrous Controller Signal Cable with 6 pin 3/8" x 3/8" connector.  Contains:  0-5V TPS Enable Input,  Enable Ground, Lockout/Tire Spin Ground, RPM Input, +12V Timing retard Output.
  • Generic JMS Progressive Nitrous Controller Signal Cable with 6 pin 3/8" x 3/8" connector.  Contains:  0-5V TPS Enable Input,  Enable Ground, Lockout/Tire Spin Ground, RPM Input, +12V Timing retard Output.
  • About to test another batch of JMS Progressive Nitrous Controllers

JMS

JMS Progressive Nitrous Controller

$399.00
Quantity:

Product Description

 
JMS Progressive N20 Controller
 
The Progressive Nitrous Controller that is designed to out perform!

The JMS Progressive N20 Controller is the new standard for Nitrous Controllers! Finally, there is a N20 Controller that allows for maximum ADJUSTABILITY while combining all of the popular nitrous add-ons into one device. No external relays, triggers or RPM Switches required...it’s all in one device!

 

 
  • Easy to setup and use. No relays, triggers, or RPM switches required, everything is built into one unit!
  • Compatible with all 12V or 16V battery systems & one to sixteen cylinder engines.
  • Adjustable Solenoid Frequency
  • Wide-Open Throttle Enable Trigger
  • Wide-Open Throttle Enable Trigger
  • Dual Independent Ramp Rates

Simple Installation:

Easy to setup and use.  No need for a laptop or complicated user display.  All adjustments can be made with the included flat-head screwdriver.

Complete Progressive Nitrous System Control in a single unit: eliminate external relays, triggers and RPM switches

Case/Enclosure Specifics and Dimensions:

Silver, Aluminum Case with four mounting tabs

Length:  5 1/2", Width:   2 1/2", Height:  1 1/2"

Operating Voltage Range:

9.5V - 20V DC

Compatibility:

- Works with all 12V or 16V battery systems.

- Supports all engines from One to Sixteen cylinders, Four Stroke or Two Stroke

- Automatically functions as a Turbo Nitrous Controller, if the Start Percentage is set higher than the End Percentage.

Inputs:

RPM:  Monitors Engine RPM.  Connect to the negative side of the ignition coil or fuel injector.

Wide Open Throttle Enable Trigger:

   Trigger (1) :  Ground Enable, typically connected to a micro-switch and grounded at WOT.

   Trigger (2):   0-5V DC (invertable), typically connected to a Throttle Body TPS. 

          Notes:  Either WOT Trigger may be used to enable the controller.

                     The enable voltage must be set by the user.

Tire Spin /Gear Lock Out:  

    Ground Enabled: Typically connected to a micro-switch.

    Depending on when this input is grounded:  can either manually lock the controller OFF or

    can be used to enable a second progressive ramp rate setting.

Outputs:

55amp maximum combined Fuel & Nitrous Solenoid Ouput

+12V Timing Retard Ouput, 50mA, short circuit protected

Adjustable Solenoid Frequency:

    12.5hz, 20hz, 25hz, 40hz  (special solenoids are required for 40hz)

Independent Fuel and Nitrous Solenoid Control:

Increased amperage capacity

Improved solenoid accuracy and control

Fuel Solenoid Settings:

The fuel solenoid output can be independently modified to control activation lean spikes.

-  100% duty cycle

-  85% duty cycle for the initial 0.5 seconds after activation and then matches the Nitrous Solenoid Ouput

-  75% duty cycle for the initial 0.3 seconds after activation and then matches the Nitrous Solenoid Output

RPM Window Switch:

Minimum RPM to enable Nitrous Output:     1000 RPM

Maximum RPM to disable Nitrous Output:  16,900 RPM

12V Timing Retard Output:

+12v output when the Nitrous Output is active

Designed to be connected to an ignition box timing retard input.

Installation Kit:

3 feet of power/solenoid wiring, wiring harness, heat shrink connectors, heat shrink ring terminal, self tapping screws, tie straps

Download the Product Technical Information Sheet
Download the NOS Controller Instructions
Download the NOS Controller Diagram
 
 Installation Video:
 
 
 Product Video:
 
 
 Product Video:
 

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

Write your own product review

Product Videos

JMS - 2011 Mustang GT Auto 3.15 Gear + JMS Nitrous Kit pn: NOS-5000 = 11.14@123mph!! (02:13)
JMS - 2011 Mustang GT Automatic with 3.15 Gear + JMS Nitrous Kit = 11.14@123mphStock = 376rwhp / 365ft-lbsAdd JMS custom Ecu Calibration Result = 390rwhp / 374ft-lbsAdd JMS Nitrous Kit PN: NOS-5000 Result = 520rwhp / 556ft-lbsTrack results = 7.07@100mph - 1/8th 11.14@123mph - 1/4 mile New 1/8th mile best of: 6.91@103mph!!! For more information visit: www.jms-nos.comorCheck out the coverage of the JMS Nitrous Kit in the April 2012 Issue of Muscle Mustangs & Fast Fords Magazine.Follow us on the web at: www.jmschip.com www.facebook.com/jmschips www.youtube.com/jmschipPhone: 601-766-9424JMS Chip & PerformanceHwy 63 SLucedale, MS 39452At JMS: we make fast cars even faster!
  • JMS Progressive Nitrous Controller Configuration and Installation - pn: NOS-6021
    Installation of the JMS Progressive Nitrous Controller - pn: N...
  • JMS 2011+ Mustang 5.0L NOS Kit Installation - pn: NOS-5000 with JMS Progressive Controller NOS-6021
    JMS 5.0L 2011+ Mustang Nitrous Kit Installation Video - Part N...
  • JMS - 2011 Mustang GT Auto 3.15 Gear + JMS Nitrous Kit pn: NOS-5000 = 11.14@123mph!!
    JMS - 2011 Mustang GT Automatic with 3.15 Gear + JMS Nitrous...

Find Similar Products by Category